Search results for "Vickers hardness test"
showing 10 items of 21 documents
Reactive Sintering of molybdenum disilicide by Spark Plasma Sintering from mechanically activated powder mixtures: Processing parameters and properti…
2008
Abstract Dense molybdenum disilicide with a nano-organized microstructure was synthesized by mechanical activation, by producing nanostructured agglomerates of a 1:2 mixture of Mo and Si, followed by the synthesis/consolidation in one step using SPS technology. In order to synthesize a dense molybdenum disilicide with a perfectly controlled microstructure, an investigation of the influence of Spark Plasma Sintering processing parameters (temperature, heating rate, mechanical pressure and holding time) on the chemical composition and the microstructure characteristics has been performed. The present work shows also that the so-obtained materials present better oxidation resistance in compari…
A time based objective evaluation of the erosive effects of various beverages on enamel and cementum of deciduous and permanent teeth
2019
Background Erosion of the teeth is a chronic irreversible process leading to loss of surface enamel and even the dentin, in turn causing sensitivity and pain. Increased consumption of carbonated beverages remains a major cause for dental erosion. However, many of the so called safe beverages that are consumed may also have sufficiently low pH to cause dental erosion. One of the parameters to measure the dental erosion is estimation of hardness and surface roughness. Thus, this study aims to evaluate the difference in hardness and surface roughness of enamel and cementum using three beverages namely (carbonated drink, lime soda, lime juice) in deciduous and permanent teeth. Material and Meth…
InBO3 and ScBO3 at high pressures: an ab initio study of elastic and thermodynamic properties
2016
We have theoretically investigated the elastic properties of calcite-type orthoborates ABO(3) (A= Sc and In) at high pressure by means of ab initio total-energy calculations. From the elastic stiffness coefficients, we have obtained the elastic moduli (B, G and E), Poisson's ratio (nu), B/G ratio, universal elastic anisotropy index (A(U)), Vickers hardness, and sound wave velocities for both orthoborates. Our simulations show that both borates are more resistive to volume compression than to shear deformation (B > G). Both compounds are ductile and become more ductile, with an increasing elastic anisotropy, as pressure increases. We have also calculated some thermodynamic properties, like D…
High-pressure x-ray diffraction andab initiostudy ofNi2Mo3N,Pd2Mo3N,Pt2Mo3N,Co3Mo3N, andFe3Mo3N: Two families of ultra-incompressible bimetallic inte…
2010
We have studied by means of high-pressure x-ray diffraction the structural stability of ${\text{Ni}}_{2}{\text{Mo}}_{3}\text{N}$, ${\text{Co}}_{3}{\text{Mo}}_{3}\text{N}$, and ${\text{Fe}}_{3}{\text{Mo}}_{3}\text{N}$. We also report ab initio computing modeling of the high-pressure properties of these compounds, ${\text{Pd}}_{2}{\text{Mo}}_{3}\text{N}$ and ${\text{Pt}}_{2}{\text{Mo}}_{3}\text{N}$. We have found that the nitrides remain stable in the ambient-pressure cubic structure at least up to 50 GPa and determined their equation of state. All of them have a bulk modulus larger than 300 GPa. Single-crystal elastic constants have been calculated in order to quantify the stiffness of the i…
Enhanced thermoelectric performance in the p-type half-Heusler (Ti/Zr/Hf)CoSb0.8Sn0.2 system via phase separation
2014
A novel approach for optimization of the thermoelectric properties of p-type Heusler compounds with a C1b structure was investigated. A successful recipe for achieving intrinsic phase separation in the n-type material based on the TiNiSn system is isoelectronic partial substitution of Ti with its heavier homologues Zr and Hf. We applied this concept to the p-type system MCoSb0.8Sn0.2 by a systematic investigation of samples with different compositions at the Ti position (M = Ti, Zr, Hf, Ti0.5Zr0.5, Zr0.5Hf0.5, and Ti0.5Hf0.5). We thus achieved an approximately 40% reduction of the thermal conductivity and a maximum figure of merit ZT of 0.9 at 700 °C. This is a 80% improvement in peak ZT fr…
Swift-ion-induced hardening and reduction of dislocation mobility in LiF crystals
2008
Ion-induced change in Vickers hardness and arm length of dislocation rosettes created by indentation on the (1 0 0) face of LiF crystals was studied. The irradiations were performed using swift U, Bi and Ni ions with a specific energy of 11 MeV per nucleon at fluences between 106 and 1013 ions cm−2. Remarkable effects of the ion-induced hardening and reduction of dislocation arm length were observed above the threshold fluences of about 109–1010 ions cm−2 and 106–107 ions cm−2, respectively. The products of track core damage and aggregates of single defects in the halo of overlapping tracks are responsible for the effects. The results are analysed using the Orowan's model of dislocation imp…
Microhardness and adhesion measurements of reactively sputtered TiN/AlN multilayer coatings deposited as function of mass-flow of nitrogen
1998
Abstract Multilayer coatings of (Ti, Al)N x have been deposited by reactive sputtering from Ti and Al targets in a side-by-side configuration on WC and stainless steel substrates. The rotation of the substrate holder varied from 2 to 14 r.p.m. corresponding to a bilayer thickness of 0.8–8 nm. The acoustic emission scratch technique for adhesion measurements was used for studying coating performance, and critical load values for the coatings on WC substrate up to 150 N were obtained. The Vickers microhardness in the load range 0.003–2 N was measured, and in order to obtain true hardness values, an optimal range of indentation depth and coating thickness was determined. Depending on the nitro…
Effect of different bleaching protocols on whitening efficiency and enamel superficial microhardness
2018
Background Tooth bleaching is a popular aesthetic treatment to modify the color of teeth. Despite the extensive literature concerning the subject, there is still no consensus regarding the application mode of the different bleaching agents and their effect on enamel. Therefore, this study evaluated the influence of different bleaching protocols on whitening efficiency and enamel superficial hardness. Material and methods Bovine enamel fragments were embedded in acrylic resin and wet-sanded to obtain a flat buccal surface. The specimens were then randomly divided into 6 groups (n=10), based on the bleaching material [HP Maxx 35% (35% hydrogen peroxide), HP Blue 35% (35% hydrogen peroxide + C…
Ceramic/metal nanocomposites by lyophilization: Spark plasma sintering and hardness
2014
The present study is focused on the procedure of spray-drying and lyophilization techniques for the preparation of ceramic/metal nanocomposites. The results of the study at all stages are compared with those corresponding to powders conventionally dried by heating in furnace. Starting from aqueous solutions of metal salts and ceramic powders, the procedure follows with spray-drying, lyophilization, calcination of the resulting powders and subsequent Spark Plasma Sintering (SPS). X-ray diffraction analysis of the powders at different stages of the processing routes was used for phase indexing; further characterization was performed by Transmission Electron Microscopy and Energy Dispersive X-…
Light transmittance of zirconia as a function of thickness and microhardness of resin cements under different thicknesses of zirconia
2012
Objective: The objective of this study was to compare microhardness of resin cements under different thicknesses of zirconia and the light transmittance of zirconia as a function of thickness. Study design: A total of 126 disc-shaped specimens (2 mm in height and 5 mm in diameter) were prepared from dual-cured resin cements (RelyX Unicem, Panavia F and Clearfil SA cement). Photoactivation was performed by using quartz tungsten halogen and light emitting diode light curing units under different thicknesses of zirconia. Then the specimens (n=7/per group) were stored in dry conditions in total dark at 37°C for 24 h. The Vicker's hardness test was performed on the resin cement layer with a micr…